By admin | Uncategorized

Most UK steam showers need a 3-9kW generator, and steam rooms often sit at the higher end of that range. Work out your own figure by measuring your room’s length, width, and height in feet for its cubic footage, adjusting upward for exterior walls, glass, and stone, then dividing by 45-50 to get the kW your space needs.
If you’re staring at a spec sheet full of kW numbers with no idea which one is yours, you’re not alone… it’s the single most common question we get asked before an order goes in. By the end of this guide you’ll have worked out your own figure, not guessed at someone else’s. We’ll cover the maths in three steps, what changes (and what doesn’t) between a steam shower and a steam room, and what actually goes wrong if you get it wrong.
Forget square footage… this is a volume calculation, because steam has to fill a space, not just cover a floor.
Measure the length, width, and height of the enclosed steam space in feet, then multiply all three together. That’s your room’s cubic footage.
One thing to measure first: measure the enclosure itself, not the whole bathroom. A steam shower cabin or a dedicated steam room has a sealed volume that’s usually much smaller than the room it sits in, and that sealed volume is what the generator actually has to heat.
Q: Does it matter if my ceiling is higher than standard?
A: Yes… a taller enclosure has more volume to fill, so it needs a bigger figure at the next step, even if the floor area hasn’t changed.
Here’s the bit people miss: two rooms with identical floor dimensions can need different generator sizes, because what the room is built from changes how much heat it loses.
This is a general steam-industry adjustment method, not a figure unique to any one retailer or brand, so you’ll see the same rough numbers wherever you check.
Add these adjustments to your base cubic footage and you get what the industry calls your adjusted cubic footage… the number that actually drives the next step.
[Explainer diagram: flat-vector “Room Volume → Adjustments → kW” flow… base cubic footage, the adjustments from the previous section, then the division step below]
Straight answer: divide your adjusted cubic footage by 45-50 to get the kW figure your room needs. That range (roughly 1kW for every 45-50 adjusted cubic feet) is the widely-used steam-industry guideline, not a figure we’ve invented for this page.
If your number lands between two standard generator sizes, round up, not down. A generator that’s slightly oversized for the room runs more efficiently; one that’s undersized works harder, heats more slowly, and tends to need servicing sooner.
Buy for the room you’ve got, not the one in the photo. The glossy lifestyle shot on a product page was taken in a specific-sized enclosure… yours might not match it.
No… the formula and the unit are exactly the same for a steam shower cabin and a dedicated steam room. What changes is the room itself.
A steam room is usually a larger enclosed volume than a steam shower cabin, so it typically needs a generator at the higher end of the kW range, or above it. To put real numbers against that: a 2.8kW generator is a genuine example of what’s fitted into a compact steam shower enclosure like the RSS1000, while a 4.5kW generator is a size more commonly specified for a larger, purpose-built steam room.
Q: So “how do I size a steam room” is the same question as “what size steam shower generator do I need”?
A: Yes, with one difference… run the same cubic-footage calculation, but expect the answer to come out bigger, because the room usually is.
Worked through the maths above? Good… check your figure against SPW’s free sizing calculator before you order, so you’re confirming your own number rather than relying on a single pass of mental arithmetic.
If you’ve already settled on an Insignia model specifically, our Insignia-specific sizing breakdown walks through exactly which Insignia generator step matches which room size. This guide’s job is the maths that works whichever brand you end up choosing.
Part P of the Building Regulations requires that the electrical connection into a steam generator is installed by a Part P-qualified electrician because every steam generator needs a hard-wired supply, not a plug-in connection, whatever size you land on. According to Checkatrade’s own cost guide, that electrician’s side of the job typically adds a few hundred pounds to the overall install, on top of the generator itself.
Once you’ve got your figure, you can see where it sits against the full range of steam showers stocked across different cabin sizes and footprints, and compare it with the steam shower cabins buying guide if you’re still deciding on the cabin itself before the generator. Models like those in the Insignia steam shower range list their generator kW on the product page, so you can match it straight against the figure you’ve just worked out.
Bottom line: measure twice, order once. Check your room’s size against SPW’s full steam generator range and you’ll order the kW your room actually needs, not the one that happened to be on offer.

Q: What is a good size for a steam shower?
A: Most home steam showers whether buying new or converting an existing shower. need a 3/9kW generator. Work it out from your room’s adjusted cubic footage divided by 45-50, or check the figure against SPW’s free sizing calculator before you order.
Q: How do I size a steam room?
A: The same cubic-footage-to-kW method as a steam shower… measure the enclosed volume, adjust for walls, glass, and stone, then divide by 45-50. Steam rooms are usually a bigger enclosed volume, so they often land at the higher end of the range.
Q: How do I calculate the steam generator capacity for my room?
A: As a guide, measure length, width, and height in feet to get cubic footage, adjust upward for exterior walls, stone or extra glass, then divide the total by 45-50 for the kW figure your room needs.
Q: Does a steam shower need the same size generator as a steam room?
A: The calculation method is identical, but a steam room’s larger enclosed volume usually means a bigger generator. A 2.8kW unit is a realistic fit for a compact steam shower like the RSS1000, while 4.5kW is more typical for a dedicated steam room.
Q: Can I size my own steam generator or do I need an electrician to confirm it?
A: You can work out the kW figure yourself using the method above. The electrical connection still needs a Part P-qualified electrician, since every steam generator runs on a hard-wired supply rather than a standard plug.